Fluke Norma 6000 Series



This email address is being protected from spambots. You need JavaScript enabled to view it.


Jakarta Office : 021-45850618

   Surabaya Office : 031-8421264

Fluke Norma 6000 Series Portable Power Analyzers


Promo Fluke Voucher Diskon

The Fluke Norma 6000 Series Portable Wideband Precision Power Analyzers give you more freedom than ever before to make high accuracy power measurements wherever you need to—whether in the lab, or in the field. Designed for portability the lightweight, battery powered Fluke 6000 Series eliminates the need to carry large, fragile, expensive analyzers into the field, allowing you to make measurements directly at the load in nearly any environment. By measuring directly at the load, you can discover how the equipment operates under real-world conditions, with real-world variables, not just at a test bench or in the lab.

With the addition of optional measurement accessories, you can even make measurements up to 1,500V DC and 2,000A AC+DC on conductors with a diameter of up to 52mm. The instrument’s compact, battery-powered design combined with a wideband frequency response makes it easier than ever to make measurements on hard to access systems such as inverter drive systems, DC-AC and AC-DC power conversion systems and electric motors without removing them from service. Making these measurements in the field simplifies the troubleshooting and performance measurement processes without sacrificing uptime, giving you more accurate test results that will enable you to discover whether your loads are operating as effectively and efficiently as they should be.

Fluke 6003 Power Analyzer

The Fluke 6003 includes three measurement channels which each consist of a voltage and current input making it ideal for three-phase power measurements.

Fluke 6004 Power Analyzer

The Fluke 6004 includes four measurement channels giving it the capability to measure three-phase power and DC power simultaneously to enable real-time inverter efficiency measurements under real-world conditions.

Fluke 6003+ and Fluke 6004+ Power Analyzer

The Fluke 6003+ and 6004+ models both add the capability to measure mechanical parameters such as speed and torque (from separate transducers) to discover the electrical to mechanical efficiency of the load under a variety of typical operating modes. 

  •     Highly portable and easily installed in tight spaces—only 9.6 cm thick.
  •     Operate continuously for up to 10 hours without an external power supply using the 5000mAh Li-ion Internal Battery.
  •     Measure safely—safety rated for CAT III 1000V, CAT IV 600V environments.
  •     Measure three phase power and DC output power at the same time with 3 or 4 channel models, with voltage and current inputs on each channel.
  •     Make mechanical torque and speed measurements using the included inputs and outputs of the Fluke 6003+ and 6004+.
  •     0.1% accuracy, 500kHz bandwidth, 200ks/s sample rate so you can rely on the power conversion system measurements you take no matter what distortion may be present.
  •     USB and RS485 interface and open communication protocol for easy system integration and software platform flexibility.
  •     Combine two analyzers to enable simultaneous measurement of multiple circuits for even more troubleshooting capability—configurable to 6 or 8 channels using dual analyzer synchronization.
  •     View critical data in the field on the main display—Meter, Waveform, Harmonics up to the 100th, Vector and Trend.
  •     Ensure high common-mode rejection and allow flexible configurations according to measurement requirements using the electrically isolated channels.
  •     User adjustable measurement rate from 100ms to 1s with continuous logging via 32GB of onboard storage.
  •     Easy in-field set up using the integrated front panel or a remote PC connection (USB or RS485).
  •     Online measuring, data download and analysis with included PC software (Fluke Power Analyzer Software).
  •     Full remote control of the connected instrument using Fluke Power Analyzer Software and a local USB or long-distance RS485 connection.




Inputs Norma 6003 3 Voltage + 3 Current
Norma 6003+ 3 Voltage + 3 Current + 1 Motor
Norma 6004 4 Voltage + 4 Current
Norma 6004+ 4 Voltage + 4 Current + 1 Motor
Sample rate 200ks/s
Measurement update rate 100ms, 200ms, 500ms, 1s
Dimensions (H * W * L) 298mm x 215m x 96mm
Weight 3.5 kg (7.7 lbs)
Display 5.7 inch, TFT LCD, 640x480
Operating temperature -10 °C to +50 °C
Storage temperature -30 °C to +60 °C
Operating humidity Non-condensing (< 10 °C )
≤ 90 % RH (at 10 °C to 30 °C)
≤ 75 % RH (at 30 °C to 40 °C)
≤ 45 % RH (at 40 °C to 50 °C)
Operating altitude 2000m
Storage altitude 12000m
Ingress protection IP 50 (Terminals mated) according to IEC 60529:
Battery BP 291, 10.8V/5000mAh, 54Wh IEC 62133, UN38.3
Operating time: 10 Hours (on battery)
Safety IEC 61010-1: Pollution Degree 2
IEC 61010-2-030: CAT IV 600V, CAT III 1000 V
EMC IEC 61326-1: Industrial
IEC 61326-2-2
Warranty 1 Year
Communication Interface USB/RS485
Dual Analyzer Synchronization Mode Able to extend to 6, 7 or 8 channels (using multiple instruments)
PC Software Fluke Power Analyzer software
Storage Capacity 32GB
Data trend storage rate As per display rate
Main Function Meter, Scope, Harmonic, Phasor, Trend
Measuring Parameters RMS, DC Component, AC Component, Rectified Mean, Peak Value, Peak-Peak, Crest Factor, Form Factor, Fundamental Component, Fundamental Content, Harmonic Distortion, Harmonic Content, Harmonic Factor for voltages and currents, Active Power, Reactive Power, Apparent Power, Power Factor, Phase Shift, Efficiency, Impedance, Electric Energy, Charge/Discharge capacity (Ah), Frequency, Motor Speed, Torque, Mechanical Power, Mechanical Energy, Summation function
Electrical Specifications
Range 10 V, 100 V, 1000 V
Crest Factor CF ≤ 2
Maximum Voltage 10 % overload
Input Impedance 2M Ω/10pF (Typical)
Temperature Coefficient 0.05 * (Spec)/k
Bandwidth 1000V range: 500kHz; 100V range: 200 kHz; 10V range:100 kHz
CMRR 120 dB @ 50/60 Hz
Accuracy (% reading + % range)
Range 1000 V 100 V 10 V
DC 0.1 + 0.1 0.1 + 0.1 0.1 + 0.2
AC (10Hz to 1kHz) 0.1 + 0.1 0.1 + 0.1 0.1 + 0.2
AC (10kHz) 5 + 0.5 5 + 0.5 5 + 0.5
Crest Factor CF ≤ 2
Temperature Coefficient 0.05 x (Spec)/k
Overload capacity 10 % overload
CMRR 120 dB @ 50/60 Hz
Shunt (current input)
Measuring Range 0.1 A, 1 A, 10 A
Input Impedance 0.025 Ω (Typical)
Bandwidth 10 A range: 500 kHz; 1 A range: 200 kHz; 0.1 A range: 100 kHz
BNC (voltage input)
Range 0.1 V, 1 V, 10 V
Input Impedance 100k Ω/100pF (Typical)
Bandwidth 10 V range: 500 kHz; 1 V range: 200 kHz; 0.1 V range: 100 kHz
Accuracy (% reading + % range)
Range 10 A 1 A 0.1 A 10 V 1 V 0.1 V
DC 0.1 + 0.2 0.1 + 0.5 0.1+2 0.1+0.1 0.1+0.2 0.1+1
AC (10Hz to 1kHz) 0.1+0.1 0.1+0.2 0.1+1 0.1+0.1 0.1+0.1 0.1+0.5
AC (10kHz) 5+1 5+1 5+1 5+1 5+1 5+1
Motor Module (Torque and Speed)
Voltage Range ± 10 V dc, 10 % overload
Voltage Channels 2
Input Impedance 1.1M Ω (Typical)
Accuracy at dc 0.1 % range + 0.1 % reading
Pulse Channels 3
Pulse Logic High Threshold 2 V (Typical)
Pulse Logic Low Threshold 0.8 V (Typical)
Maximum Pulse Frequency 100 kHz
Motor Module (Torque and Speed)
Frequency Accuracy 0.05 % range + 0.05 % reading
Harmonics 100 (50Hz/60Hz)
Calculation method FFT/Interpolation



Model Name Description Price
Norma 6003 Portable Power Analyzers Get a Quote
Norma 6003+ Portable Power Analyzers Get a Quote
Norma 6004 Portable Power Analyzers Get a Quote
Norma 6004+ Portable Power Analyzers Get a Quote


Power Quality Software Downloads

To ensure your product has the latest software release that include new features, click on the appropriate link below and follow the download instructions.

Fluke 1736 and 1738 Power Logger


Last updated

Fluke Energy Analyze Plus v2.2 (.exe) »
Fluke Energy Analyze Plus application software for download, analysis and reporting. Used with Fluke 1730, 1736 and 1738. (Compatible with Windows 7, 8 and 10).


Fluke Energy Analyze Plus v2.2 Release notes (.pdf) »
Fluke Energy Analyze Plus application software for download, analysis and reporting. Used with Fluke 1730, 1736, and 1738. (Compatible with Windows 7, 8 and 10).


Fluke 173x v2.0 Firmware File (.bin) »
To upload directly to Fluke 1736 from USB create a directory titled “Fluke1736” on the USB stick and copy the firmware file to that directory location.

To upload directly to Fluke 1738 from USB create a directory titled “Fluke173x”, copy the firmware file to that directory location, and rename it to “173x_firmware_2.0.bin”.

Plug the USB stick into the instrument, if the firmware is a later version than the one on the instrument the automatic update process will proceed. Last updated

Available Licenses*:

  • Free License to implement WiFi Infrastructure connection (on registration)
  • Fluke 1736 to 1738 upgrade
  • IEEE519 Reporting License


*Please contact your local Fluke representative for more information.
Firmware v2.0 is the minimum requirement for installation of these licenses.


Ladbrokes Review L.BetRoll
Top United Kingdom Bookmakers http://betroll.co.uk/